All unfinished parts have been CNC inlet to Boyds' House Action. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ĪTTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.ĬLASSIC, MAUSER, SMALL RING, # 1 BARREL CHANNEL, LH STOCK, RH ACTIONīarrel Dimensions: Point A = 1 3/16" and Point B = 7/8"Ĭenter to Center of Action Screws: 7 5/8"Ĭomes with Boyds' 1/2" Rubber Recoil Pad. Final sanding and finish will be required. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required.All unfinished parts have been CNC inlet to Boyds' House Action. PRAIRIE HUNTER, MAUSER LR, MILITARY BARREL CHANNEL, ZZīarrel Dimensions: Point A = 1 1/8" and Point B = 13/16"Center to Center of Action Screws: 7 7/8"Front Receiver Ring: 1 3/8"Overall Length of Floor Plate: 8 11/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed to accept the military stepped barrel minus sight sleeve. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. These are available from gun parts stores such as Midway USA or Brownells.Īll finished parts have been CNC inlet to Boyds' House Action. the Action Bars are pinned to the fore arm and are integral, you will need to purchase the appropriate length/gauge of two piece Slide Action Tube and Slide Action Tube Nut. If you have a one piece Slide Action Tube, i.e. there is a Slide Tube nut that holds the fore arm onto the Action Tube. ATTENTION: Boyds Mossberg pump action fore arms (500 & 835) are designed for a two piece Slide Action Tube, i.e. You may contact Havlin Sales at 63 to obtain proper components. If you have one of these, you cannot use a forearm that was designed to go over an action slide tube without first buying the correct length tube and action slide tube nut. If your action slide measures 6 1/2", see our American Plainsman Bantam Forend Shape! NOTE: Since 2006, some newer models shotguns with synthetic forearms may not use an action slide tube at all rather, the pump handle will have two integral bars pinned into the handle itself. This measurement is critical! This forend is for the 7 5/8" action slide. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/2 Magazine Tube Shoulder to Shoulder: 6 3/4 Over All Length of Part: 9 1/4ĪTTENTION CUSTOMERS : On your action slide tube, measure from top of threads to bottom of collar that holds the action bars. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 diffrent types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.:All finished parts have been CNC inlet to Boyds' House Action. ![]() 770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. PRO VARMINT, REMINGTON® 770, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNELīarrel Dimensions:where barrel meets reciever/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B =.
0 Comments
Leave a Reply. |